An Easy Guideline On The Best DIY Backpacking Stove

DIY backpacking stove

Best DIY Backpacking Stove For Your Camping Trip

When you go on a backpacking trip, a set of essential items is required to sustain yourself on the field.  In order to make hot meals and warm beverages, there is hardly that can perform as good as a stove. Backpacking stoves are available in large number and can be found pretty much everywhere. But you can cut back the expense by making a stove by yourself instead of buying one from the store. If it’s also your desire then this article is for you. Read through the below and learn how to create the best DIY backpacking stove with some stuff you found around the house.

To a minimalist, a DIY backpacking store is an excellent choice for a heating source. It’s light, very easy to use and cost almost nothing to build. However, there are several notable shortcomings which make it not really suitable for complex and complicated demands. You have little to no control over the strength of the flame and the fuel efficiency is generally low that require constant refills. Nerveless, it will do just fine as a secondary or backup stove when it comes to basic tasks. You are not going to whip up a full course meal with this type of stove anytime soon though.

You may like to see this: The Best Backpacking Stove You Can Own For The Money

Preparing materials and tools

  • Body of the stove: You need something with high thermal conductivity. Aluminum cylinder – shape bottle and alike should be enough
  • Powered saw: Due to the hardness of the material, this is necessary to cut through its layer
  • Drill: To supply the fire with oxygen, holes must be made along the body so ensure you have one by your side.
  • Tape measure and a permanent marker: For measuring and marking. They are dandy when you need to keep up the precise specifications of the stove  
  • Safety Operation: This is number one priority, therefore, prepare sandpaper to sand and smoothen sharp edges and cuts. Equip yourself with a pair of goggles and mask as well  

A couple kind of fuel can be used to run the stove with examples such as liquid fuel, fuel tablet and wood. You can find such fuels in the average hardware store or even salvage around the campsite. Each of them has unique pros and cons which fit a variety of user preferences.

  • Liquid fuel: Easy to ignite but needs careful handling
  • Fuel tablet: Compact yet its chemical smell is kind of bad
  • Wood: Can be found by walking around the camping area but if there is too much humidity, it may be hard to prime the stove.

When you have everything, let’s get to work

Building the best DIY backpacking stove in 5 steps

  • Step 1: Measure and cut

DIY backpacking stove 1

Via: survivalistprepper

You will need to cut the bottle into three pieces. Measure from the bottom up two inches and make a mark. Do the same but this time you start from the top and go down. Next, use the saw and cut the marks to separate the bottle. Try your best to keep the cut along the marks and maintain the two inches specification. Place the two inches pieces side by side to determine if you have done a good job. You are going to press them together soon so make sure that they are usable. Move on to the next step if the pieces are OK.

  • Step 2: Drill some holes

DIY backpacking stove 2

If you go with liquid fuel, the base piece holes should be located about one and a half inch from the top. Spread them in a way that they are equally spaced around the outer layer. Do not punch all the way through or the stove may not function properly.  There is no need to drill holes in the top piece. In the case that you go with other types of fuel, do the same with the base piece but the top piece needs to be drilled as well. Mark then creates a ring of holes slightly below where the structure starts to expand.

For the size of the holes, 1/16 drill bit is sufficient but you can also use 1/32 one. If you decide to go with the smaller bit, double the number of holes to make up for the limited size.

  • Step 3: Combine the two inches pieces

DIY backpacking stove 3

Place the bottom piece facing up and turn the top piece upside down then clamp them into each other. If you decide to use liquid fuel, leave a small gap between the pieces so the fuel can flow into the chamber.  Otherwise, apply as much pressure as you can and push the top piece all the way into the bottom piece. When you are done, both of the pieces shall merge into a single unit. After that, grab some sandpaper and process the only open end so it’s safe to use and won’t scratch your cookware.

  • Step 4: Finish

With a stove like this one, aesthetic value is not really the most important issue but do whatever you want. You can outfit the stove with miscellaneous features such as a handle or a stand if you wish. Just remember not to make it too bulky or cumbersome which can result in awkward carrying.

  • Step 5: Fuel and light

DIY Backpacking stove 4

The stove is now completed, all you need to do is put in the fuel and fire it up. Remember not to overfill or the flame can get out of control. While DIY stove has no simmer control, it should be enough to boil a couple cups of water in approximately 5 – 10 minutes. The boiling time depends largely on the fuel you are using and the weather condition. When the environment humidity level is high or there are violent winds, expect the boiling time to fluctuate a lot from normal.

Related Post:

Conclusion

And that should be most of the basic on how to create the best DIY backpacking stove, fairly easy to take in, right? The stove is surely not the best to use but hardly anything can beat it in simplicity and weight. The construction is extremely robust and straightforward that everybody can make one at their house. If you want to quickly craft up a stove in an emergency, this is the design that you should go after.

Home | Camping | Survival

Add Comment